| Citation: | LIU Li, YAO Peng, CHU Dong-kai, XU Xiang-yue, QU Shuo-shuo, HUANG Chuan-zhen. Laser-assisted water jet machining of high quality micro-trap structures on stainless steel surfaces[J]. Chinese Optics, 2024, 17(6): 1476-1488. doi: 10.37188/CO.EN-2024-0004
|
Secondary electron emission (SEE) has emerged as a critical issue in next-generation accelerators. Mitigating SEE on metal surfaces is crucial for enhancing the stability and emittance of particle accelerators while extending their lifespan. This paper explores the application of laser-assisted water jet technology in constructing high-quality micro-trap structures on 316L stainless steel, a key material in accelerator manufacturing. The study systematically analyzes the impact of various parameters such as laser repetition frequency, pulse duration, average power, water jet pressure, repeat times, nozzle offset, focal position, offset distance between grooves, and processing speed on the surface morphology of stainless steel. The findings reveal that micro-groove depth increases with higher laser power but decreases with increasing water jet pressure and processing speed. Interestingly, repeat times have minimal effect on depth. On the other hand, micro-groove width increases with higher laser power and repeat times but decreases with processing speed. By optimizing these parameters, the researchers achieved high-quality pound sign-shaped trap structure with consistent dimensions. We tested the secondary electron emission coefficient of the "well" structure. The coefficient is reduced by 0.5 at most compared to before processing, effectively suppressing secondary electron emission. These results offer indispensable insights for the fabrication of micro-trap structures on material surfaces. Laser-assisted water jet technology demonstrates considerable potential in mitigating SEE on metal surfaces.
| [1] |
LI SH J, YU X, DANG X Q, et al. A novel double dielectric barrier discharge reactor with high field emission and secondary electron emission for toluene abatement[J]. Plasma Science and Technology, 2022, 24(1): 015504. doi: 10.1088/2058-6272/ac17e4
|
| [2] |
PINTO P C, CALATRONI S, NEUPERT H, et al. Carbon coatings with low secondary electron yield[J]. Vacuum, 2013, 98: 29-36. doi: 10.1016/j.vacuum.2013.03.001
|
| [3] |
AYZATSKY M I, DOVBNYA A N, ZAKUTIN V V, et al. The electron accelerator based on the secondary emission electron source for material-surface treatment[C]. Proceedings of RuPAC 2006, 2022.
|
| [4] |
WANG D, CAI Y H, HE Y N, et al. Electron emission properties of silver oxide and its impact on the secondary emission yield of air-exposed silver[J]. Results in Physics, 2022, 33: 105231. doi: 10.1016/j.rinp.2022.105231
|
| [5] |
CUI X, GILARDONI S, GIOVANNOZZI M, et al. Numerical simulations of electron-cloud build up in circular accelerators in the presence of multimode-distribution beams[J]. Europhysics Letters, 2020, 129(2): 24003. doi: 10.1209/0295-5075/129/24003
|
| [6] |
DONG Y, DONG ZH W, YANG W Y, et al. Monte Carlo simulation of multipactor discharge suppressing on grooved dielectric surface[J]. High Power Laser and Particle Beams, 2013, 25(2): 399-406. (in Chinese). doi: 10.3788/HPLPB20132502.0399
|
| [7] |
BOZEMAN S P, BAUMANN P K, WARD B L, et al. Electron emission measurements from CVD diamond surfaces[J]. Diamond and Related Materials, 1996, 5(6-8): 802-806. doi: 10.1016/0925-9635(95)00417-3
|
| [8] |
TOKUDA N, UMEZAWA H, SAITO T, et al. Surface roughening of diamond (001) films during homoepitaxial growth in heavy boron doping[J]. Diamond and Related Materials, 2007, 16(4-7): 767-770. doi: 10.1016/j.diamond.2006.12.024
|
| [9] |
LIU Y, LIANG CH H, MEI C X, et al. Influence of coating on the secondary electron emission coefficient of metal surface[J]. Journal of Xianyang Normal College, 2018, 33(6): 50-52. (in Chinese). doi: 10.3969/j.issn.1672-2914.2018.06.012
|
| [10] |
WEI Q, WU SH L, FU M L, et al. Attenuation mechanism of secondary electron effect of MgO film under electron bombardment[J]. Journal of Xi'an Jiaotong University, 2017, 51(11): 125-129. (in Chinese). doi: 10.7652/xjtuxb201711017
|
| [11] |
VALIZADEH R, MALYSHEV O B, WANG S H, et al. Low secondary electron yield engineered surface for electron cloud mitigation[J]. Applied Physics Letters, 2014, 105(23): 231605. doi: 10.1063/1.4902993
|
| [12] |
WANG Y G, ZHANG W L, WANG S H, et al. Influence of primary electron incident angle and electron bombardment on the secondary electron yield of laser-treated copper[J]. Journal of Vacuum Science & Technology B, 2021, 39(3): 034201.
|
| [13] |
CHENG B, DING Y, LI Y, et al. Coaxial helical gas assisted laser water jet machining of SiC/SiC ceramic matrix composites[J]. Journal of Materials Processing Technology, 2021, 293: 117067. doi: 10.1016/j.jmatprotec.2021.117067
|
| [14] |
NARGUNDKAR A, GULIA V, KHAN A. Nanoabrasives-assisted abrasive water jet machining of bio-composites— an experimental and optimization approach[J]. Journal of Advanced Manufacturing Systems, 2023, 22(4): 799-822. doi: 10.1142/S0219686723500373
|
| [15] |
TANGWARODOMNUKUN V, WANG J, HUANG C Z, et al. An investigation of hybrid laser–waterjet ablation of silicon substrates[J]. International Journal of Machine Tools and Manufacture, 2012, 56: 39-49. doi: 10.1016/j.ijmachtools.2012.01.002
|
| [16] |
惠庆志. 激光辅助水射流加工4H-SiC材料的工艺与去除机理研究[D]. 济南: 山东大学, 2018: 29-31, 49-52.
HUI Q ZH. Study on process and material removal mechanism for micromachining 4H-SiC by laser assisted waterjet[D]. Jinan: Shandong University, 2018: 29-31, 49-52. (in Chinese).
|
| [17] |
FENG SH CH, HUANG CH ZH, WANG J, et al. Material removal of single crystal 4H-SiC wafers in hybrid laser-waterjet micromachining process[J]. Materials Science in Semiconductor Processing, 2018, 82: 112-125. doi: 10.1016/j.mssp.2018.03.035
|
| [18] |
张晨旭. 激光辅助水射流切割氧化铝陶瓷的可加工性研究[D]. 济南: 山东大学, 2016: 35-41, 47-48.
ZHANG CH X. Study on the machinability of alumina ceramics by laser assisted waterjet[D]. Jinan: Shandong University, 2016: 35-41, 47-48. (in Chinese).
|
| [19] |
ZHAI SH J, FENG Q G, YANG H, et al. Liquid-phase assisted laser preparation of 304 stainless steel surface texture and tribological properties evaluated[J]. Industrial Lubrication and Tribology, 2022, 74(6): 654-662. doi: 10.1108/ILT-12-2021-0499
|
| [20] |
ELSHORBAGY M H, SÁNCHEZ-BREA L M, BUENCUERPO J, et al. Polarization conversion using customized subwavelength laser-induced periodic surface structures on stainless steel[J]. Photonics Research, 2022, 10(9): 2024-2031. doi: 10.1364/PRJ.454451
|
| [21] |
LI Y CH, ZHANG X B, MAO ZH, et al. Study on size and morphology control of 316L stainless steel microgrooves processed by ultraviolet nanosecond laser[J]. Applied Laser, 2019, 39(6): 994-1001. (in Chinese).
|
| [22] |
DUAN R H, LIU ZH Q, WANG X, et al. Effect of abrasive water jet - plasma nitriding duplex treatment on friction property of 316 stainless steel surface[J]. Surface Technology, 2020, 49(7): 149-158. (in Chinese).
|
| [23] |
LI Q, SUN G F, LU Y, et al. Experimental research on fiber laser underwater cutting of 1 mm thick 304 stainless steel[J]. Chinese Journal of Lasers, 2016, 43(6): 57-66. (in Chinese).
|
Figures(12) / Tables(1)
DownLoad:
