电机补偿式焦度仪镜片参数的计算

张永玲

电机补偿式焦度仪镜片参数的计算

张永玲

中北大学光电仪器厂,山西太原030051

详细信息

作者简介:
张永玲(1983—),女,山西大同人,硕士,助理工程师,主要从事视光学仪器的设计及图像处理方面的研究。 E-mail:tianlemxn@163.com

中图分类号: TH741.4
计量
- 文章访问数: 4075
- HTML全文浏览量: 596
- PDF下载量: 1573
- 被引次数: 0
出版历程
- 收稿日期: 2011-02-12
- 修回日期: 2011-04-23
- 刊出日期: 2011-06-25

Calculation of lens parameters for lensmeters based on motor compensation

ZHANG Yong-ling

Optical Instrument Factory of North University of China,Taiyuan 030051,China

摘要

摘要: 针对目前市场上测量眼镜片相关参数全自动焦度仪测量范围小、测量精度较差等问题,研制了基于电机补偿原理的焦度仪。该焦度仪采用步进电机带动分划板做线性运动对分划板的位置进行补偿,通过改变焦度仪光学系统的物像关系来提高焦度仪的测量精度,扩大它的测量范围。测量时放入待测镜片,待整个调节过程结束后,电器部件会将每个接收到的图像进行分析计算后取平均值,得到待测镜片的各项参数。利用本样机对一些典型镜片进行了测量,结果显示所有镜片的误差范围均在0.02 m-1内,表明本文研制的焦度仪完全符合国家计量检定规程的计量检定要求。
- 焦度仪 /
- 电机补偿 /
- 镜片参数
Abstract: Automatic lensmeter is an instrument for measuring optical parameters of glasses. For several universal problems on the small measurement range and poor accuracy of the automatic lensmeter, this paper developeds a instrument. It uses motor compensation principle to adjust the linear motion position of a partition board to implement the compensation, and changes the relation of the images and the object to achieve the focal power measurement accuracy and enlarge the measuring range. When a lens is placed in the optical system until the end of the adjustment process, the electrical components will receive the image and analyze the averaged calculation, which can get the parameters of the lens under test. After a system demonstration and testing, the prototype is used to successful measure some typical lenses. The results show that all lenses are in the range of error within 0.02 m-1. The measurement results fully meet the requirements of national metrological verification test.
- lensmeter /
- motor compensation /
- lens parameter

HTML全文

参考文献(1)

[1] 刘晨,张辉,柯玉军 .自动焦度计的研制[J]. 光学仪器 ,2003,25(6):40-44. LIU CH,ZHANG H,KE Y J. Development of automatic lensmeter[J]. Opt. Instruments,2003,25(6):40-44.(in Chinese) [2] 王文华,何斌,任建岳 . 线阵CCD成像系统自校图形设计[J]. 光学精密工程 ,2009,17(8):2011-2015. WANG W H,HE B,REN J Y. Design of self-check figures in linear CCD imaging system[J]. Opt. Precision Eng.,2009,17(8):2011-2015.(in Chinese) [3] 刘志艳,陈香才,江晓山,等. 用于高速线阵CCD的数据获取系统[J]. 核电子学与探测技术 ,2010(6):722-725. LIU ZH Y,CHEN X C,JIANG X SH,et al.. A data-acquisition system for high speed linear CCD[J]. Nuclear Electronics Detection Technol.,2010(6):722-725.(in Chinese) [4] 徐正平,翟林培,葛文奇,等. 亚像元的CCD几何超分辨方法[J]. 光学精密工程 ,2008,16(12):2447-2453 XU ZH P,ZHAI L P,GE W Q,et al.. CCD geometric super resolution method based on sub pixel[J]. Opt. Precision Eng.,2008,16(12):2447-2453.(in Chinese) [5] 李林 . 工程光学 [M].北京:北京理工大学出版社,2003. LI L. Engineering Optics[M]. Beijing:Beijing University of Technology Press,2003.(in Chinese) [6] 胡家升.光学工程导论 [M].大连:大连理工大学出版社,2002:835-846. HU J SH. Introduction to Optical Engineering[M]. Dalian:Dalian University of Technology Press,2002:835-846 (in Chinese). [7] 王和顺,陈次昌,黄惟公. 提高CCD测量精度的方法研究[J]. 光电子·激光 ,2010(1):63-65. WANG H SH,CHEN C CH,HUANG W G. Research the method to improve CCD measurement accuracy[J]. J.Optoelectronics·Laser,2010(1):63-65.(in Chinese) [8] 马振亚,王莉茹,刘文丽. GB 17341-1998中华人民共和国国家标准:光学和光学仪器-焦度仪[S]//全国光学和光学仪器标准化技术委员会.北京:中国标准出版社,1998:3-6. MA ZH Y,WANG L R,LIU W L. GB 17341-1998 National Standard of the People's Republic of China-Optics and Optical Instruments-Focimeters[S]//The national optical and optical instruments standardization technical committee. Beijing:China Standards Press,1998:3-6.(in Chinese) [9] 王莉茹,张吉焱,刘文丽,等. JJG580-2005中华人民共和国国家计量检定规程-焦度计[S]//全国光学计量技术委员会.北京:中国计量出版社,2005:4-6. WANG L R,ZHANG J Y,LIU W L,et al. JJG580-2005 The People's Republic of China National Metrological Verification Procedures:Focimeters[S]//The national optical measurement technology committee. Beijing:China Metrology Press,2995:4-6.(in Chinese)

施引文献

附加信息(0)

访问统计